Global Auto Parts & Accessories Marketplace
Home » Product Directory » Electricity & Electronics » Electronics Parts » Relay »

LD1041 Auto Moto Flsher Relay ICs Integrated Circuits Auto Ics

    • Application: Acura, Alfa romeo, Aston ...
    • OEM No/Model: LD1041
    • Market Type:After Market 
    • Price: Inquiry For It?
    • Payment Terms: L/C, T/T
    • Samples: Free
    • Minimum Order: 10Piece/Pieces

Quick Details

  • Place of Origin:

    CHINA

  • Samples:

    Free

  • Delivery Time:

    Delivery After Payment

  • Packing:

    DIP-8 50Pcs/Tube 40Tubes/Box 10Boxes/Carton SO-8 100Pcs/Tube 100Tubes/Box 10Boxes/Carton

  • Delivery Port:

    Dalian

  • Max. Production Capacity:

    1000000

  • Export Ratio:

    41% - 50%

  • OE Experience:

    No

Product Name:LD1041 Auto Moto Flsher Relay ICs Integrated Circuits Auto Ics

LD1041 Auto Moto Flsher Relay ICs Integrated Circuits Auto Ics

Application

Acura; Alfa romeo; Aston martin; audi; Aux; Baolong; Beiqi; Bentley; BMW; Bugatti; Buick; BYD; cadillac; Changan; Changfeng; Chery; chevolet; Chrysler; Citroen; Dadi; DAEWOO; Daihatsu; Dodge; Dongfeng; DADI Auto; Ferrari; fiat; Ford; Foton; Fuqi... More

Product Description:

OEM No/Model: LD1041

Automotive Direction Indicator ICs


Deacription
LD1041 (analog UAA1041B) was designed for use in conjunction with a relay in automotive applications. It is also applicable for other warning lamps such as “handbrake ON,” etc.

Features
Defective Lamp Detection
Overvoltage Protection
Short Circuit Detection and Relay Shutdown to Prevent Risk of Fire
Reverse Battery Connection Protection
Integrated Suppression Clamp Diode   Circuit Description
The circuit is designed to drive the direction indicator flasher relay. Figure 1 shows the typical system configuration with the external components. It consists of a network (R1, C1) to determine the oscillator frequency, shunt resistor (RS) to detect defective bulbs and short circuits in the system, and two current limiting resistors (R2 / R3) to protect the IC against load dump transients. The circuit can be used either with or without short circuit detection, and features overvoltage, defective lamp and short circuit detection.
The lightbulbs L1, L2, L3, L4 are the turn signal indicators.  When switch  K1 is closed, after a time delay of t1 (in our example t1≈75 ms), the relay will be actuated.  The corresponding lightbulbs  (L1, L2 or L3, L4) will flash at the oscillator frequency, independent of the battery voltage of 8.0 V to 18 V. The flashing cycle stops and the circuit is reset to the initial position when switch K1 is open.

Overvoltage Detection
Senses the battery voltage. When this voltage exceeds 20.2 V (12V Flasher) or 30.5V (24 Flasher), (this is the case when two batteries are connected in series), the relay will be turned off to protect the lightbulbs.

Lightbulb Defect Detector
Senses the current through the shunt resistor RS. When one of the lightbulbs is defective, the failure is indicated by doubling the flashing frequency.

Short Circuit Detector
Detects excessive current (Ish > 25 A) flowing in the shunt resistor RS. The detection takes place after a time delay  of  t3  (t3 ≈ 55 ms).  In this case, the relay will be turned off.  The circuit is reset by switching S1  to the off position.

Operation with Short Circuit Detection
Pin 6 has to be left open and a capacitor C2 has to be connected between Pin 1 and Pin 2.

Operation without Short Circuit Detection
 Pin 6 has to be connected to Pin 2, and the use of capacitor C2 is not necessary. The circuit can also be used for other warning flashers.
  Application Information
1. The flashing cycle is started by closing K1.
The switch position is sensed across resistor R2 and RLamp by Input pin 8. Rst = R2 + RLamp.
The condition for the start is: Rst < 3.6 kΩ.
For correct operation, leakage resistance from Pin 8 to ground must be greater than 5.6 kΩ.
2. Flashing frequency: fn = 1/ (R1×C1×Kn)
3. Flashing frequency in the case of one defective lightbulb of 21 W:
                                             fF = 1 / (R1×C1×KF)     Kn = 2.2KF
4. t1: delay at the moment when K1 is closed and first flash        t1 = K1×R1×C1
5. t2: defective lightbulb det6. t3: short circuit detection delay  
   
Company Name: Dandong Huaao Electronics Co., Ltd.
Address: No.64 Taoyuan street, Dandong, Liaoning, China           

Send your message to this supplier:

logo Ms. Nan Li
Enter between 20 to 3,000 characters, English only.

Supplier Details

Dandong Huaao Electronics Co. , Ltd

Market Type: After Market 
Business Type: Manufacturer
Main Product: Integrated Circuits and Power Transistors for Automobile

You May Like:

LT4761 Auto Moto Flasher Relay IC Direction Indica ... Application: Acura, Alfa rome ...
OEM No: LT4761
LD6046 LD6047 U6046 U6046B U6047 U6047B Auto Rear ... Application: We are Dandong H ...
OEM No: LD6046/ ...
LD2044 Auto Moto Dual Output Flasher Relay Flasher ... Application: Acura, Alfa rome ...
OEM No: LD2044
3735014-V08 Flash Relay FOR Great Wall Application: Great Wall
OEM No: 3735014 ...
Relay 4117-U-Z 2X10A DC12V For FIAT PUNTO 188 Stee ... Application: Relay 4117-U-Z
OEM No: AW-REY- ...
2019 Bestselling 24V 30A For Mitsubishi MC843788 5 ... Application: for Mitsubishi
OEM No: MC84378 ...
Relay For Mitsubishi Pickup L200 Sport K94W K96W K ... Application: Mitsubishi L200 ...
OEM No: MB18386 ...
RELAY 704011 FOR STARTER MOTOR Application: BOSCH KB SERIES ...
OEM No: 704011
Mitsubishi Motor Parts, Glow Relay, Auto Relay Application: Mitsubishi
OEM No: Univers ...
Didn't find what you are looking for?
Please send us Your Search Requirement, or you can Post a Buying Lead,
suppliers may contact you actively.

Send Message