Quick Details

• Place of Origin:

  CHINA

• OE Experience:

  No

Product Name:VW Fuel Injector 037906031AL Auto Injectors Auto Parts Car Parts Car Accessories

VW Fuel Injector 037906031AL Auto Injectors Auto Parts Car Parts Car Accessories

Application

volkswagen

Product Description:

OEM No/Model: 037906031AL

Volkswagen fuel injector : 037906031AL 

  Product Information Manufacturer Part Number: A2C59513199,

 fuel: gasoline

used in vehicles:

Renault Clio II (BB0/1/2_, CB0/1/2_) 1.4 (B/CB0C) (KBA numbers HSN / TSN: 3004/127; year 09.1998 -05.2005, 55KW, 75HP, 1390ccm)

Renault KANGOO (KC0/1_) 1.4 (KC0C, KC0H, KC0B, KC0M) (KBA numbers HSN / TSN: 3004/554; Year 08.1997, 55KW, 75HP, 1390ccm);

Renault KANGOO (FC0/1_) 1.4 (FC0C, FC0B, FC0H, FC0M) (KBA numbers HSN / TSN: 3004/007; Year 08.1997, 55KW, 75HP, 1390ccm)

Renault MEGANE I (BA0/1_) 1.4 e (BA0E, BA0V) (KBA numbers HSN / TSN: 3004/738; Year 01.1996, 55KW, 75HP, 1390ccm)

 Renault MEGANE Grandtour (KA0/1_) 1.4 e (KA0V) (KBA numbers HSN / TSN : 3004/595; Year 03.1999, 55KW, 75HP, 1390ccm)

What is fuel injector?

An injector, ejector, steam ejector, steam injector, eductor-jet pump or thermocompressor is a type of pump that uses the Venturi effect of a converging-diverging nozzle to convert the pressure energy of a motive fluid to velocity energy which creates a low pressure zone that draws in and entrains a suction fluid. After passing through the throat of the injector, the mixed fluid expands and the velocity is reduced which results in recompressing the mixed fluids by converting velocity energy back into pressure energy. The motive fluid may be a liquid, steam or any other gas. The entrained suction fluid may be a gas, a liquid, a slurry, or a dust-laden gas stream

The adjacent diagram depicts a typical modern ejector. It consists of a motive fluid inlet nozzle and a converging-diverging outlet nozzle. Water, air, steam, or any other fluid at high pressure provides the motive force at the inlet.

The Venturi effect, a particular case of Bernoulli's principle, applies to the operation of this device. Fluid under high pressure is converted into a high-velocity jet at the throat of the convergent-divergent nozzle which creates a low pressure at that point. The low pressure draws the suction fluid into the convergent-divergent nozzle where it mixes with the motive fluid.

In essence, the pressure energy of the inlet motive fluid is converted to kinetic energy in the form of velocity head at the throat of the convergent-divergent nozzle. As the mixed fluid then expands in the divergent diffuser, the kinetic energy is converted back to pressure energy at the diffuser outlet in accordance with Bernoulli's principle. There are very few steam locomotives still in operation today other than as tourist attractions. However, when steam locomotives were in use many years ago, injectors were used to pump water into the locomotive's steam-producing boiler and some of the steam was used as the injector's motive fluid. Such "steam injectors" took advantage of the latent heat released by the resulting condensation of the motive steam.

Depending on the specific application, an injector takes the form of an eductor-jet pump, a water eductor, a vacuum ejector, a steam-jet ejector, or an aspirator.

We carry:

Jinjiang Junri Machinery Co., Ltd., established in 1991, is a joint venture enterprise.Our factor locate in Fujian Province, China. Our company is one of the leading manufacturers in China specialize in Diesel engine auto spare parts such as nozzles, plungers, delivery valves, distribution head ...[Read More]

Company Profile:

• Main Product:

  Nozzles, Plungers, Delivery Valves, Distribution Head Pumps and Repair Kits.

• Business Type:

  Manufacturer

• Current Export Market:

  South America, Southeast Asia, Mid East, Africa

Factory Profile:

• Number of Employees:

  51 - 100 People

• Size of Factory In Square Meters:

  7000

• Years of OEM Experiences:

  19

• Certification:

  ISO 9001

Research & Development:

• Capability for Synchronized Development:

  Develop according to drawing or samples provided by clients?Yes

  Develop 3-D model and prototype according to client's needs?No

• Tooling Design:

  Design Internally

• Source of Tooling:

  Made Internally