Launch ATF Changer (CAT-401) 1.I ntro: The transmission fluid inside transmission will go bad for a period of usage of automatic transmission. If the transmission fluid can not be changed completely in time, it may cause the abnormality to the transmission. General auto transmission fluid changer can not control the filling quantity of the ATF as required, the excessive or shortage filling will cause the damage to auto transmission. CAT-401 auto transmission changer can complete the flush and fluid exchange in 20 minutes for transmission, torque converter and radiator. The fluid 2.Feature : * LCD display and compact design making easy operation. * Automatic filling of automatic transmission fluid. * Automatic identification of the power polarity. * Automatic and intelligent switch the fluid flow in and out direction. * Automatic circulated cleaning function of automatic transmission. * Automatic exchange of new/used fluid. * Visual display the fluid pressure of A/F radiator and the fluid outlet pressure of the unit
Balancing Machine for Auto Brake Vertical Dynamic Balancing Machine:Single Plane Vertical Balancing Machine: This kind of balancing machine is a new and widely-used device which has been available and developed in recent years. It is mainly applied to balance all kinds of discoid parts, such as fanbrake diskbrake drumsawbladebelt pulley,bit tool etc .. High speed and precision are its advanages. Specifications Parameters Max Mass of Workpiece (with clump) (kg) 65 Max Diameter of Workpiece (mm) 800 ( if the machine is without cover)/510 (with cover). Height of Workpiece (mm) 160 Rotation Speed of Main Axis (r/min) 700 Motor Power (kw) 2.2 Min Achievable Residue Unbalace Amount (emar) 5g· mm/kg
Movable wire fabrication AC Spot Welder DN10,DNJ16,DNJ25; major citcuit uses controlled high speed,spark free thyristor Movable wire fabrication AC Spot Welder With small volume and light weight,the spot welder can be moved freely.major citcuit uses controlled.high speed,spark free thyristor as switch DNJ10 Spot Welder , DNJ16 Spot Welder ,DNJ25 Spot Welder has seven steps of welding currents and takes 0-3 seconds to adjust them. It also has conneected two cables in venting water(2m).a hand -holding spot welding torch, and a spot welding clamp. It is mainly designed for needs of sheet metal and wire fabrication. portable spot welding machine DNJ10 DNJ16 DNJ25 Rated capacity 10KVA 16KVA 25KVA Rated input voltage single380V single380V singIe380V Rated input Current 26.3A 42,1A 66A Number of grade 7 7 7 Output cable length 2m 2m 2m Applicable thickness 0.61.5mm 0.6-2rnrn 13mm Cooling mode Transformer wind cooling Output cable water cooling We are Manufacturers and exporters of Welding machines in CHINA. products: inverter DC MMA welding machines, inverter DC TIG welding machines, inverter AC/DC TIG welding machines, inverter pulse TIG/MMA welding machines, inverter DC TIG/MMA welding machines, inverter plasma cutting machines, inverter MMA/TIG/CUT multi-functional machines, CO2 MIG/MAG machines submerged arc welding machines If you have interest in them, please feel free contact us.
Clutch Dynamic Balancing Machine: This balancing machine is a new and widely-used device which has been available and developed in recent years. It is mainly applied to balance all kinds of discoid parts, such as fanbrake diskbrake drumsawbladebelt pulley,etc .. High speed and precision are its advanages. Specifications Parameters Max Mass of Workpiece (with clump) (kg) 16 Max Diameter of Workpiece (mm) 800 ( if the machine is without cover)/510 (with cover) Height of Workpiece (mm) 160 Rotation Speed of Main Axis (r/min) 900 Motor Power (kw) 1.1 Min Achievable Residue Unbalace Amount (emar) 5g· mm/kg
Launch CNC-601 Fuel Injector Cleaner: 1.Introduction CNC-601A injector cleaner & tester manufactured by LAUNCH TECH CO., LTD. Developed with the technology of ultrasonic cleaning and fuel pressure control, CNC-601A is an advanced electromechanical product, which can clean and test injectors by simulating engine working conditions. It can also perform cleaning on the injectors and fuel supply system on vehicle. 2. Specification * Power supply: AC220V±10%, 50/60Hz;AC110V±10%, 50/60Hz. * Input power: 250W; * Ultrasonic cleaner power: 100W; * Simulated RPM range: 109990rpm ; step: 10rpm; * Time range: 19999s; * Pulse width: 0.525ms; step 0.1 ms; * Fuel tank capacity: 4700ml ; * Dimensions: 385mm×410mm×500mm ; * Weight: About 35kg 3. Feature * Ultrasonic cleaning: To perform simultaneous cleaning on several injectors and to remove the carbon deposits on the injector completely. * Uniformity/Sprayability test: To test the uniformity of injecting amount of each injector, and to monitor the spraying status of each injector with the help of backlight. This test is also for reverse flush. * Leakage test: To test the sealing and dribbling conditions of injectors under system pressure. * Injecting flow test: To check the injecting amount of the injector in 15 seconds of constant injection. * Auto. test: To test injectors by simulating different working conditions. * On-vehicle cleaning: The unit is equipped with various adaptors and couplers that facilitate cleaning on the injectors on vehicle.
Product Name: Restorer of rain sensor TS16949 Correct methods: Rub the rein sensor iasc soand-fro rn 10cm disiance slowly and it is forbidden so polishthe entire Icaihvcrtical as to aioid damage to the rain sensor arid beating up of the resiorer.Origiul wipers effect better Usage: 1.Pull up or remove the rain sensor while cleaning with tissue, and stuck the leash of the rain sensor by the rain sensor mate, rubbing to-and-fro in 10cm distance slowly. 2.Rubbing it by the thicker side as marked, then use thinner side and put back. Test rub with water and rub the unsatisfied part. 3.The rain sensor for sedan limousine must be rubbed slowly. Precautions: 1.Rubbing the rain sensor may produce sudden heat causing the leash to melt and adhere to the channel slot, which will damage the rain sensor and restorer. Therefore, it is forbidden to polish the entire leash vertically as to avoid heating up. It is recommended to wipe dry the rain sensor before rubbing, otherwise it may affect the effect by the leash powder rubbed and adhere to the restorer.
Paint Dryer TBM-132 : Specification : 1.No, of tubes (paces)1 2.Length of heater tubes (cm) 58 3.High temperature 800 4.Moderate temperature 800 5.Voltage Input(V): 220 6.Distance from panel (cm) 45 7.Time(min) 15~30 8.Coverage area(L*W) (cm*cm)60*65 function features * using special shortwave infrared quartz glass as the heat source which the light-wave offers powerful penetrability. * ultrasonic has automatic distance detection capability, auto-distance protection function, real-time distance display function(optional). * semi-power automatic paint function. * automatic timer control (range of 0-60 minutes are free to choose) and real-time time digital display function. * automatic alarm and reminder functions. * automatic computer control and digital display computing function. * lamps are rotatable through three-dimensional direction, and they can changed any position and angle that make sure to work convenient for car's painting. * the equipment can be used to dry automobile resin putty, two-component paint and water base coating. it has widely scope of application. * lamp cover adopts stainless steel with shining mirror-like. surface, reflective effect good, thermal gather homogeneously. * short drying time to ensure high proficiency and high quality of painting surface. * four groups touching button respectively control, flexible operation. * bracket is made of metal alloy, strong, beautiful and durable. * detached structural design, the casters, it can move freely, trouble free and convenient. * wheels with brake are good use of position fixed when the equipments worked. * non-contact infrared temperature detection function automatically, automatic temperature protection function, real-time temperature display functions(optional). * high and low temperature paint selection and automatic control functions(optional).
Product Name: Restorer of rain sensor National top fifty Correct methods: Rub the rein sensor iasc soand-fro rn 10cm disiance slowly and it is forbidden so polishthe entire Icaihvcrtical as to aioid damage to the rain sensor arid beating up of the resiorer.Origiul wipers effect better Usage: 1.Pull up or remove the rain sensor while cleaning with tissue, and stuck the leash of the rain sensor by the rain sensor mate, rubbing to-and-fro in 10cm distance slowly. 2.Rubbing it by the thicker side as marked, then use thinner side and put back. Test rub with water and rub the unsatisfied part. 3.The rain sensor for sedan limousine must be rubbed slowly. Precautions: 1.Rubbing the rain sensor may produce sudden heat causing the leash to melt and adhere to the channel slot, which will damage the rain sensor and restorer. Therefore, it is forbidden to polish the entire leash vertically as to avoid heating up. It is recommended to wipe dry the rain sensor before rubbing, otherwise it may affect the effect by the leash powder rubbed and adhere to the restorer.
Transmission Shaft Balancing Machine This balancing machine is equiped with hard bearing structure. With the advantages of high measuring speed, high precision, easy to load and unload, it is an ideal device for shaft manufacturers and maintenance factories. Specifications Parameters Mass Scope of Workpiece(kg) 100 Max Diameter of Workpiece (mm) Ø130 Max Length of Workpiece (mm) 2000 Rotation Speed of the Main Axis (r/min) -3200(variable-frequency and stepless speed regulation) Motor Power (KW) 1.1(variable-frequency) Min Achievable Residue Unbalance Amounte mar 5g· mm/kg